Description:
CHRYSLER / DODGE / JEEP VEHICLES
- STE-EFM2: 2011 - 2017 Chrysler 300
- STE-EFM2: 2015 - 2017 Dodge Challenger
- STE-EFM2: 2014 - 2017 Dodge Durango
- STE-EFM2: 2009 - 2017 Dodge RAM 1500 - 5500
- STE-EFM2: 2014 - 2017 Jeep Grand Cherokee
- STE-EFM2-CHR1: 2018 - 2023 Chysler 300
- STE-EFM2-CHR1: 2018 - 2023 Dodge Challenger
- STE-EFM2-CHR1: 2018 - 2023 Dodge Charger
- STE-EFM2-CHR1: 2018 - 2024 Dodge Durango
- STE-EFM2-CHR1: 2018 - 2024 Dodge RAM 1500 - 5500
- STE-EFM2-CHR1: 2018 - 2022 Jeep Grand Cherokee
- STE-EFM2-CHR1: 2018 - 2024 Jeep Wrangler JL
- STE-EFM2-CHR1: 2020 - 2024 Jeep Gladiator
FORD VEHICLES
- STE-EFM3-FRD1: 2016 - 2019 Explorer
- STE-EFM3-FRD1: 2015 - 2019 F-150
- STE-EFM3-FRD1: 2017 - 2019 F-250 - F-550
- Newer Ford Trucks: Be sure to checkout the Z-Flash BCM Plug-n-play Module
GM VEHICLES
- STE-EFM2: 2007 - 2013 Avalanche
- STE-EFM2: 2015 - 2016 Canyon
- STE-EFM2: 2015 - 2016 Colorado
- STE-EFM2: 2010 - 2017 Equinox
- STE-EFM2: 2007 - 2016 Escalade
- STE-EFM2: 2008 - 2023 Express
- STE-EFM2: 2014 - 2017 Impala
- STE-EFM2: 2008 - 2023 Savana
- STE-EFM2: 2007 - 2016 Sierra 1500 - 3500
- STE-EFM2: 2007 - 2016 Silverado 1500 - 3500
- STE-EFM2: 2007 - 2016 Tahoe/Suburban
- STE-EFM2: 2009 - 2017 Traverse
- STE-EFM2: 2010 - 2017 Terrain
- STE-EFM2: 2007 - 2016 Yukon
- STE-EFM3-GM1: 2017 - 2022 Acadia
- STE-EFM3-GM1: 2019 - 2022 Blazer
- STE-EFM3-GM1: 2017 - 2022 Canyon
- STE-EFM3-GM1: 2017 - 2022 Colorado
- STE-EFM3-GM1: 2018 - 2022 Equinox
- STE-EFM3-GM1: 2017 - 2020 Escalade
- STE-EFM3-GM1: 2018 - 2022 Malibu
- STE-EFM3-GM1: 2017 - 2021 Sierra 1500
- STE-EFM3-GM1: 2022 Sierra 1500 LTD - LTD ONLY - NO OTHER '22 SUB-MODELS WILL WORK!
- STE-EFM3-GM1: 2017 - 2023 Sierra 2500-3500
- STE-EFM3-GM1: 2017 - 2021 Silverado 1500
- STE-EFM3-GM1: 2022 Silverado 1500 LTD - LTD ONLY - NO OTHER '22 SUB-MODELS WILL WORK!
- STE-EFM3-GM1: 2017 - 2023 Silverado 2500-3500
- STE-EFM3-GM1: 2017 - 2020 Tahoe / Suburban
- STE-EFM3-GM1: 2018 - 2021 Traverse
- STE-EFM3-GM1: 2018 - 2021 Terrain
- STE-EFM3-GM1: 2017 - 2020 Yukon
Note: Please do not call about vehicle compatabilty. If your vehicle is not listed above, then it will not be compatible. If there were more 2023 & 2024 compatible models, they would be listed.
Easy Flash Module 2.0 & Easy Flash Module 3.0 Features:
The Speed Turtle Easy Flash Module provides a simple and effective way to flash the factory exterior lights of supported vehicles. The system is easily installed in minutes and is a true plug and play solution.
If equipped and supported, the module will flash the following lights:
- Front Low Beams
- Front High Beams
- Front Turn Signals
- Front Fog Lamps
- Front LED Accents
- Rear Turn Signals
- Rear Stop Lamps
- Third / Center Mounted Brake Lamp
- Reverse Lamps
- Rear LED Accents (2.0 Module Only)
- Pickup Bed Lamp
Unlike other solutions, these modules do not require any cutting or reconfiguration of the vehicle's wiring harness. This allows the module to be easily installed by anyone in minutes. The plug and play installation also allows the module to be removed and installed in another vehicle without repairing or replacing vehicle components. The system works while parked and in motion. The module has two switch inputs as well as an existing vehicle button that can be configured to activate the module either through a long press or quick cycle.
Choose from one of the following switch interface harnesses:
Toggle Switch Harness: This harness provides a simple ON/OFF toggle switch with adhesive backing. There are two internal LEDs to the toggle switch with green indicating the switch is OFF and orange indicating the switch is ON. While this is the simplest of the two harnesses to install, it only provides one of the two possible switch inputs. The toggle switch harness is connected to Input 1 on the module.
Voltage Input Harness: This harness provides two flying lead' input wires. Each wire will accept a 5 17 volt input signal from a switch or light controller of your choice. The white wire corresponds to Input 1 and the green wire corresponds to Input 2.
Kit includes:
- Easy Flash Module 2.0 (OBD) or 3.0 (BCM)
- Switch interface harness of your choosing
- 6' micro USB cable
- Zip ties
Installation:
The 2.0 STE-EFM2 versions simply plugin to your vehicle's OBD port.
The 3.0 STE-EFM3 version uses an included wiring harness to easily plug in to your BCM. There is no hard-wiring required, just attaching some clip-in wiring bundles.
Speedturtle YouTube installation video's are provided for your reference.
Do you need to order the Chrysler ODB Pass Through device seperately?